Makita 18V X2 (36V) LXT Brushless 9 in. Power Cutter Kit(5.0 Ah) and 9 In. Diamond Blade, Segmented w/ bonus 18V LXT Work Light XEC01PT1E025DML

About This Product

The 18V X2 (36V) LXT Brushless 9” Power Cutter Kit (XEC01PT1) has the power to cut through various materials with all the benefits and convenience of cordless operation. The XEC01PT1 has a maximum cutting depth of 3-1/2”, thus can cut through standard residential concrete slab in a single pass. Besides concrete, it has the power to cut through I-beams, steel pipe (3”), rebar (3/4” -#6), metal stud (14” wide) and more. The benefits of a cordless power cutter over a gas power cutter include no oil/gas mixing, no emissions, no pull starts, no engine maintenance, and lighter weight. This means reduced operator fatigue, instant starts, cost savings, and the ability to use the power cutter indoors, in tight spaces, and high elevations. An integrated water delivery system continuously feeds water for OSHA Table 1 Compliance in concrete cutting applications. Water flow is controlled with an adjustment knob. The belt-drive design provides smoother operation with lower vibration. The XEC01PT1 has a purpose-built BL Brushless Motor, which eliminates carbon brushes and enables the motor to run cooler and more efficiently for longer life. The brushless motor delivers 6,600 RPM. The kit includes the power cutter, four 18V LXT 5.0Ah Batteries, a dual-port charger, and a Diamond Blade and Cut-Off Wheel. This Promotion also includes an E-02515 9 in. Diamond Blade, Segmented, General Purpose and comes with a bonus DML811 18V LXT Lithium-Ion Cordless/Corded Work Light (Light Only).

Highlights

XEC01PT1 - Eliminates the hassles of gas with lower weight, reduced maintenance, and zero emissions allowing use in indoor environments

XEC01PT1 - The BL Brushless Motor powered by two 18V LXT Lithium-Ion batteries eliminate the hassle of engine pull starts allowing immediate starts-up (batteries not included)

XEC01PT1 - The BL Brushless Motor eliminates carbon brushes, enabling the BL Motor to run cooler and more efficiently for longer life; delivers 6,600 RPM

XEC01PT1 - Integrated water delivery system with water flow adjustment knob continuously feeds water for OSHA Table 1 Compliance in concrete cutting applications

XEC01PT1 - Active Feedback-sensing Technology (AFT) turns the motor off if rotation of the wheel is suddenly forced to stop

XEC01PT1 - Electric brake stops the wheel in 4 seconds or less allowing for faster re-positioning

XEC01PT1 - Built-in L.E.D. light with an independent on/off switch illuminates the cutting area for increased visibility

XEC01PT1 - Makes single pass cuts up to a 3-1/2" depth in various masonry and metal materials

XEC01PT1 - Integrated overload indicator alerts of excessive battery power draw during heavy loads (batteries not included)

XEC01PT1 - Overload protection is designed to protect the motor from burnout in abnormally high torque situations

XEC01PT1 - Soft start suppresses start-up reaction for smoother start-ups and longer gear life

XEC01PT1 - Protective battery compartment helps prevent dust and slurry contamination

E-02515 - Taller 13mm segments are designed for longer life and faster cutting

E-02515 - Up to 4x longer life than competitive blades

E-02515 - For cutting concrete, block, brick, pavers, and roof tiles

DML811 - 3-mode operation: delivers 3,000 lumens on High, 1,500 lumens on medium, and 750 lumens on Low

DML811 - Up to 3 hours of continuous illumination with a 6.0Ah 18V LXT® battery on high (battery and charger not included)

DML811 - Up to 13 hours of continuous illumination with a 6.0Ah 18V LXT® battery on low (battery and charger not included)